Table of Contents
ToggleA pressure switch looks simple, yet one stuck contact can stop a pump or trip a whole compressor train. Below you will find field checks for every common fault, a fault table and a trip and reset calculator.
Find out why a pressure switch does not trip, chatters or drifts away from its setpoint, using field checks in a fixed order. The fault table, the multimeter test and the calculator give every job a clear pass or fail.

How to do pressure switch troubleshooting step by step in the field?
Pressure switch troubleshooting means comparing the actual trip and reset pressures with the datasheet values and then checking contacts, wiring and the sensing element. Reset equals setpoint minus deadband for a rising trip. Example: a 10 bar high pressure switch with 1 bar deadband should trip near 10 bar and reset near 9 bar; if it trips at 11.2 bar, it has drifted and needs recalibration.
- Isolate the process and vent the impulse line safely.
- Check supply voltage, terminals and NO/NC wiring with a multimeter.
- Apply pressure slowly with a hand pump and reference gauge.
- Record the rising trip point and the falling reset point.
- Compare with setpoint, deadband and tolerance, then adjust or replace.
What Is Pressure Switch Troubleshooting?
Pressure switch troubleshooting means finding out why a switch does not change state at the correct pressure, or changes state when it should not. You combine a bench or in situ pressure test with electrical checks on the contacts, wiring and the receiving PLC or relay input.
- Deadband, also called differential, is the gap between trip and reset pressure.
- Tameson notes that mechanical switches typically have a deadband of 10 to 30 percent of the setpoint.
- Most faults are wrong setpoint, pulsation, failed contacts, wiring or a damaged diaphragm.
If you are new to the device, first read how a pressure switch works. The rest of this pressure switch troubleshooting guide covers the faults you will meet in a plant.
A pressure switch gives only two states, so it cannot show slow drift the way a transmitter can. Drift is usually found only during a trip test or after a real process upset.
Why Is My Pressure Switch Not Working?
A pressure switch usually stops working for one of five reasons: wrong setpoint, blocked or isolated impulse line, failed contacts, broken wiring or a damaged sensing element. The quickest way to separate them is to test the electrical side and the pressure side one at a time.
Start pressure switch troubleshooting with the simple checks: confirm the root valve is open and the line is clear, as in our impulse line testing procedure.
| Symptom | Likely Cause | Field Check | Fix |
|---|---|---|---|
| Switch never trips | Setpoint too high, isolated tap, seized mechanism | Compare local gauge with setpoint; apply test pressure | Open root valve, reset setpoint, replace if seized |
| Chattering | Pulsation, narrow deadband, setpoint near normal pressure | Watch gauge needle; log contact changes | Add snubber, widen deadband, move setpoint |
| Will not reset | Deadband too wide or manual reset type | Check nameplate | Adjust deadband or press reset |
| Signal reversed | Wired to NO instead of NC | Check terminal C, NO, NC with meter | Rewire as per loop drawing |
| Intermittent signal | Loose terminal or water in housing | Wiggle test | Retighten, dry and seal |
Before you touch the setpoint screw, write down the as found trip and reset values. Without them you cannot prove whether the switch drifted or somebody changed it.
How to Test a Pressure Switch with a Multimeter
To test a pressure switch with a multimeter, isolate the power, connect the meter in continuity or resistance mode across common and NO, and slowly raise the pressure until the reading changes from open to closed. Then lower the pressure slowly to find the reset point where the contact opens again.
Fluke describes this same manual method for pressure switch troubleshooting and calibration. The difference between the rising set point and falling reset readings is the deadband.

The reference gauge should be at least four times more accurate than the switch tolerance. Our guide on test uncertainty ratio explains this 4 to 1 target.
Once the fault is fixed, follow pressure switch calibration in 8 simple steps to record the as left values.
Pressure Switch Troubleshooting Calculator for Trip and Reset Point
This calculator works out the expected reset point from the setpoint and deadband, then checks your measured trip and reset values against the allowed tolerance. Pressure switch troubleshooting then ends in a plain pass or fail.
Falling trip: Reset = Setpoint + Deadband
Allowed error = Range × Tolerance % ÷ 100
Trip error = Measured trip minus Setpoint
Reset error = Measured reset minus Expected reset
Solved example: a 0 to 16 bar high pressure switch is set at 10 bar with 1 bar deadband and 2 percent tolerance. The measured trip of 10.3 bar and reset of 9.1 bar are checked below.
Allowed error = 16 × 2 ÷ 100 = 0.32 bar
Trip error = 10.3 minus 10 = 0.30 bar
Reset error = 9.1 minus 9 = 0.10 bar
Measured deadband = 1.20 bar, result PASS
If your gauge reads in psi, convert first with the online pressure unit converter or our psi to bar tool. For error in percent of span, use the calibration error calculator.
Why Does a Pressure Switch Chatter?
A pressure switch chatters when the process pressure moves back and forth across the setpoint faster than the deadband can absorb. Pulsation from pumps and compressors, a deadband that is too narrow, and a setpoint placed too close to normal operating pressure are the three main causes.
Whitman Controls notes that contacts bouncing near the set point confuse PLC logic and shorten relay life. It recommends a wider deadband and a snubber to smooth rapid pulses.
See pressure snubber selection for snubber types, and deadband in pressure switches for why a wider gap cures hunting.
Tameson explains that piston switches offer wide deadbands, while diaphragm and bourdon tube switches offer limited ones. A diaphragm switch on a pulsating discharge may chatter even when calibrated.
A short on delay timer in the PLC can mask bounce, much as switch debouncing does. On a safety trip, never hide chatter this way without a review.
How Do I Know If My Pressure Switch Is Bad?
A pressure switch is bad when it still fails to trip or reset within tolerance after the setpoint is corrected, or its contacts show high resistance. Visible signs include fluid inside the housing, corroded terminals and a setpoint screw that changes nothing.
Pitted or welded contacts read high resistance or stay closed.
A ruptured diaphragm stops response or leaks fluid.
Trip value moves after vibration or overpressure.
Loose cores or wrong terminals reverse the signal.
A closed contact should read near zero ohms, so several ohms or a jumping value means wear. Prove the cable with insulation resistance testing after disconnecting the PLC card.
Keep a spare switch with the same range and contact type in store. Swapping and bench testing is often faster than fault finding in a hazardous area.
NO and NC Contact and Wiring Faults
Wiring faults show up as a reversed, frozen or flickering signal. Most come from using NO where the loop drawing asks for NC, or from loose terminals.
Safety trips are wired fail safe, so the contact is closed when healthy and opens on a trip or broken wire. Check against pressure switch wiring with NO and NC before changing terminals.
- PLC input LED matches the contact state
- Glands tight and housing dry
- Ferrules fitted and screws tight
- Signal reversed against alarm logic
- Input flickers when cable moves
- Green oxide or water in terminals
Match the wiring with the card type using sinking and sourcing in PLC. After rewiring, do an instrument loop check up to the HMI alarm.
Setpoint Drift and Wrong Deadband
Setpoint drift is the slow movement of the trip value away from the set value, while a wrong deadband means the reset point is too close to or too far from the trip. Both are found only by a rising and falling pressure test.
Drift comes from spikes above the proof pressure rating, vibration and temperature swings. OMEGA advises setpoints between 20 and 100 percent of range and warns that running at proof pressure may shift the setpoint.
In the OMEGA PSW300, adjuster B sets the rising operating point and adjuster A sets the falling reset. See setpoint and deadband configuration, and always recheck the trip after setting the reset.
Pressure Switch Troubleshooting Checklist for the Field
Work through this checklist in order during pressure switch troubleshooting so nothing is missed. It runs from isolation to the process side, then the electrical checks and finally the records.
- Permit taken, process isolated and impulse line vented
- Root valve and impulse line clear
- Contact state at rest checked on C, NO and NC
- Trip and reset recorded three times
- Deadband within nameplate limits
- Snubber fitted on pulsating service
- As found and as left values recorded
Record values as shown in as found and as left records. With good records you can spot a drifting switch before it causes a shutdown.
When Should You Replace a Pressure Switch with a Transmitter?
Replace a mechanical switch with a transmitter or an electronic switch when the same unit keeps drifting, chattering or failing despite correct installation. With a continuous signal you can see the trend before the trip happens.
Compare options in pressure switch vs pressure transmitter and IO Link electronic switches. Under IEC 61511, nuisance trips also raise the spurious trip rate.
The Fluke video below shows an automatic pressure switch troubleshooting and calibration test on a 10 psi switch. Watch how slowly pressure is ramped near the setpoint.
In that Fluke example the switch set at 10.5 psi and reset near 9.5 psi, inside the 2 psi tolerance. Our calculator uses the same pass or fail logic.
Pressure Switch Troubleshooting FAQ
The first step is to compare the local gauge reading with the switch setpoint and confirm the impulse line is open. Many no trip complaints end here because the root valve was closed or the tap was plugged.
Only after that should you isolate the switch and test its contacts.
The setpoint is the pressure where the contact changes state, and the reset point is where it changes back. Deadband is the difference between them, so a 10 bar setpoint with a 9 bar reset gives a 1 bar deadband.
A wider deadband reduces chatter, while a narrow one suits alarms.
For a rising trip, subtract the deadband from the setpoint, so 10 bar minus 1 bar gives a 9 bar reset. For a falling low pressure trip, add the deadband instead, so 2 bar plus 0.5 bar gives 2.5 bar.
It chatters because pump pulsation moves pressure across the setpoint faster than the deadband can absorb. A snubber, a wider deadband or moving the setpoint further away from normal pressure usually stops it.
Confirm the cure by logging contact changes for one shift.
Set the meter to resistance and measure C to NO and C to NC at zero pressure. NO should read open and NC near zero ohms, and both must swap state when the switch trips.
This simple check is the core of electrical pressure switch troubleshooting.
The most common mistake is ramping pressure too fast, which records a false trip value. Others include skipping as found readings, using a gauge less accurate than the switch and forgetting to retest.
Always finish pressure switch troubleshooting with a final as left test.
A piston type or electronic switch with adjustable deadband and delay is usually best for pulsating service. Fit a snubber and mount the switch on a bracket or panel away from the vibrating pipe.
This prevents fatigue of the diaphragm and early setpoint drift.
Related Articles
- What Is a Pressure Switch
- Deadband in Pressure Switches
- Pressure Switch Wiring NO and NC
- Pressure Switch Calibration in 8 Simple Steps
- Pressure Transmitter Troubleshooting
External References
- OMEGA PSW300 Series Pressure Switches User Guide (PDF)
- Tameson: Understanding the deadband of a pressure switch
- Wikipedia: Pressure switch
What We Learn Today
- Pressure switch troubleshooting starts at the process tap and gauge, then moves to contacts, wiring and the sensing element in a fixed order.
- Reset point equals setpoint minus deadband for a rising trip, and the measured values must stay within the allowed tolerance of the range.
- Chattering is usually caused by pulsation or narrow deadband, and is cured with a snubber, wider deadband or a better placed setpoint.

