Table of Contents
ToggleSlew rate decides how fast an amplifier output can swing, and a slow part quietly turns clean sine waves into triangles. Below you get the formula, a worked LM741 example, a calculator and a practical way to select a part for real circuits.
Slew rate is the speed limit of an amplifier output, measured in volts per microsecond. Here is how to calculate the value your signal needs and pick a part that meets it.

What is op amp slew rate and how do you calculate it?
Op amp slew rate is the maximum rate of change of the output voltage, given in V/µs. For a sine wave the required value is SR = 2πf × Vpeak, so a 20 kHz signal with 10 V peak needs about 1.26 V/µs. An LM741 rated at 0.5 V/µs cannot do this and will output a distorted triangle, while a TL081 at 13 V/µs handles it easily.
What Is Op Amp Slew Rate?
Op amp slew rate is the fastest speed at which the output voltage of an operational amplifier can rise or fall, normally written in volts per microsecond (V/µs). When the input asks the output to change faster than this limit, the output simply ramps at its maximum speed and the waveform gets distorted.
- Unit: volts per microsecond (V/µs), quoted as a typical value in the datasheet.
- Sine wave requirement: SR = 2π × f × Vpeak.
- Full power bandwidth: FPBW = SR ÷ (2π × Vpeak).
- LM741 is about 0.5 V/µs and TL081 is about 13 V/µs, as listed in the Texas Instruments datasheets.
- Slew rate is a large signal limit, while gain bandwidth product is a small signal limit.
If you are new to amplifiers, first revise the basics of the operational amplifier such as open loop gain and the virtual short. Slew rate becomes important the moment your design has a large output swing at a reasonably high frequency, for example a unity gain buffer driving a fast square wave.
Texas Instruments explains in its note Ramping Up on Slew Rate that some modern CMOS amplifiers use a slew boost circuit. These parts slew much faster for large input steps than for small ones, so the datasheet number depends on the test condition.
Why Does the Slew Rate Limit Happen Inside an Op Amp?
The limit happens because the input stage can only supply a fixed maximum current to charge the internal compensation capacitor. A capacitor charged by a fixed current produces a voltage ramp, and that ramp speed is the slew rate.
Imax = maximum input stage current
Cc = internal compensation capacitor
All About Circuits shows the LM124 internal schematic where the compensation capacitor is clearly labelled, and the same idea applies to the classic 741. A small tail current or a big capacitor gives a slow amplifier, so low power parts are usually slow parts.
Slew rate does not change with closed loop gain in the way bandwidth does. A gain of 1 or a gain of 10 still gives roughly the same V/µs, but higher gain makes the output swing bigger and so the limit is reached sooner.
How to Calculate Required Op Amp Slew Rate?
For a sine wave, multiply 2π by the frequency and by the peak output voltage, then convert the result to V/µs. The steepest point of a sine wave is at the zero crossing, and its slope there equals 2πfVp.
Max slope = SR = 2π × f × Vp
Full power bandwidth:
FPBW = SR ÷ (2π × Vp)
For a square or step signal, the rule is different because the edge is the limit. Rise time from 10 % to 90 % is roughly 0.8 × step size ÷ SR when the output is fully slew limited.
Solved Example: Can an LM741 Pass a 20 kHz, 10 V Peak Signal?
No, an LM741 cannot pass this signal cleanly because it needs 1.26 V/µs and the part offers only about 0.5 V/µs. Its full power bandwidth at 10 V peak works out to less than 8 kHz.
SR needed = 2 × 3.1416 × 20000 × 10
SR needed = 1,256,637 V/s = 1.26 V/µs
FPBW = 0.5 × 106 ÷ (2 × 3.1416 × 10)
FPBW = 7.96 kHz
Change the last field to 13, the typical figure for a TL081, and the calculator shows a full power bandwidth above 200 kHz. With that one change, the same circuit handles any audio range signal comfortably.
In a non inverting amplifier with a gain of 11 and 1 V peak input, the output peak becomes 11 V. Always do the slew check at the output, and an op amp gain calculator helps you get that output figure quickly.
Slew Rate vs Bandwidth: What Is the Difference?
Slew rate is a large signal speed limit in V/µs, while gain bandwidth product is a small signal frequency limit in MHz. A circuit must satisfy both, and for big outputs the slew limit usually bites first.
| Point | Slew rate (SR) | Gain bandwidth (GBW) |
|---|---|---|
| Signal size | Large signal | Small signal |
| Unit | V/µs | MHz |
| Depends on | Output amplitude | Closed loop gain |
| Distortion type | Triangle shaped, nonlinear | Amplitude roll off, linear |
| Formula | FPBW = SR ÷ 2πVp | f = GBW ÷ gain |
| LM741 typical | 0.5 V/µs | About 1 MHz |
An easy way to remember it: bandwidth asks whether the amplifier can follow small fast wiggles and slew rate asks whether it can make big fast swings. The inverting amplifier gain formula tells you the gain, and from that you can check both limits in two lines.
- Clean large signal output at higher frequency
- Fast settling for ADC drivers and sample and hold circuits
- Sharp edges in comparators and pulse circuits
- Usually higher supply current and power
- Can be harder to keep stable with capacitive loads
- Often more noise or offset at the same price
How to Select an Op Amp by Slew Rate?
Calculate the slew rate your worst case signal needs, add a margin of two to five times, and then shortlist parts whose typical datasheet value is above that number. After that, check bandwidth, noise, supply range and output swing.
General purpose dual amplifier listed by Texas Instruments at about 0.3 V/µs typical.
The classic teaching part with about 0.5 V/µs typical in the TI datasheet.
Low noise dual amplifier widely used in audio, with about 9 V/µs typical.
JFET input amplifier listed at about 13 V/µs typical by Texas Instruments.
For an active Sallen and Key filter at audio frequencies, a TL081 class part is a safe and cheap choice. For a fast ADC driver, look at the settling time figure as well, because slewing plus settling decides when the sample is valid.
- Use the output peak voltage after gain, not the input peak.
- Use the highest frequency or the fastest edge in the signal.
- Compare with the typical and the minimum slew rate in the datasheet.
- Check rising and falling slew rate separately, as some parts differ.
- Keep a margin of at least two times for temperature and part spread.
Many datasheets list slew rate at unity gain with a specific load resistor and capacitor. A heavier capacitive load in your board can make the real output slower than the printed figure.
What Causes Slew Rate Distortion and How to Fix It?
Slew rate distortion happens when the output cannot keep up, so a sine wave turns into a triangle and square wave edges become slow ramps. To fix it, lower the amplitude or frequency, or move to a faster amplifier.
| Symptom on scope | Likely cause | Field fix |
|---|---|---|
| Sine becomes triangle | SR below 2πfVp | Use a faster part or reduce gain |
| Distortion only at high volume | Large swing reaches SR limit | Reduce peak swing or raise SR |
| Slow square wave edges | Fully slewing output | Check rise time against 0.8 × step ÷ SR |
| Rising and falling slopes differ | Asymmetric internal currents | Pick a part with symmetric SR |
| Ringing after the ramp | Capacitive load or low phase margin | Add an isolation resistor at the output |
Slew limited output adds odd harmonics, much like the harmonic distortion and THD you see in power systems. In audio this sound is called transient intermodulation distortion, and it is easy to hear at high volume.
Where Does Slew Rate Matter in Instrumentation?
Slew rate matters wherever an amplifier must make large and fast output swings, such as ADC drivers, comparators, pulse circuits and active filters. In slow process signals like a 4 to 20 mA loop, it is rarely the limiting factor.
For example, when you use an op amp as one of the comparator circuits, the output must swing from rail to rail, and a slow part gives very soft edges. The precision rectifier and the transimpedance amplifier for photodiodes are two more circuits where students often meet this limit in the lab.
On the bench, feed a square wave and measure the slope of the output edge between 10 % and 90 % on the scope. Divide the voltage change by the time and you have the real slew rate of your board.
Slew rate also links to noise and signal quality, so after you fix the speed, check the signal to noise ratio calculator for the full signal chain. For a refresher on both basic amplifier configurations, this inverting and non inverting amplifier guide is also useful.
Op Amp Slew Rate FAQ
Slew rate limits large signal speed in V/µs, while gain bandwidth product limits small signal frequency in MHz.
An LM741 has about 1 MHz GBW, yet at 10 V peak its slew rate of 0.5 V/µs limits clean output to under 8 kHz.
Take the output peak voltage, multiply it by 2π and by the highest frequency, then divide by one million to get V/µs.
For 5 V peak at 50 kHz, the answer is 2 × 3.1416 × 50000 × 5, which gives about 1.57 V/µs.
The sine wave turns into a triangle shaped wave because the output can only ramp at its maximum speed.
The peak amplitude also drops, and the output gains odd harmonics that raise distortion, which is clearly visible on an oscilloscope.
For audio range work, parts like the TL081 at about 13 V/µs or the NE5532 at about 9 V/µs are common choices.
Always calculate 2πfVp for your own signal first, then pick a part with two to five times that value.
Divide the slew rate in V/s by 2π times the peak output voltage.
For an amplifier with 13 V/µs at 10 V peak, the full power bandwidth is 13000000 ÷ 62.83, which gives roughly 207 kHz for a clean, undistorted sine output.
The most common mistake is using the input peak voltage instead of the output peak after gain.
A gain of 10 multiplies the needed slew rate by 10, so a part that looked fine on paper can distort badly on the bench.
Related Articles
- Operational Amplifier Basics
- Voltage Follower and Unity Gain Buffer
- Inverting Amplifier Gain Formula
- Non Inverting Amplifier Gain
- Instrumentation Amplifier vs Op Amp Key Differences
External References
- Texas Instruments: Ramping Up on Slew Rate (SLOA332)
- All About Circuits: Op Amp Slew Rate and Rise Time
- Wikipedia: Slew rate
What We Learn Today
- Op amp slew rate is the maximum output voltage change per microsecond, and it is set by input stage current charging the compensation capacitor.
- The required value for a sine wave is SR = 2πfVp, and full power bandwidth equals the slew rate divided by 2π times the peak voltage.
- Choose an amplifier with two to five times the calculated slew rate and always use the output peak after gain in the calculation.

